Vermeer TR5300 Trommel Screen
The TR5300 trommel screen is ideal for operations where high productivity in a compact size is demanded. The tensioned screen and drum are designed for optimum productivity, offering simple adjustments and maintenance. The ability for the conveyors to go parallel to the ground gives the operator more control over dust and wind, while also allowing for easier maintenance. The TR5300 features a maintenance access platform for the Deutz TD 2.9L Tier 4 Final (Stage IV), 74 hp (55 kW) engine.
- With the ability to tension the screen around the drum, operators can add rigidity to the screens. This design allows the use of smaller gauge wire, ultimately increasing the open area of the screen to help improve productivity.
- Operators can control the machine through either the Vermeer DP10 display mounted on the control panel, or through a handheld transceiver remote. From either control, the operator can choose from four programmable presets or adjust machine settings based on incoming material.
- A set of dual-hinged doors on both sides of the machine expose the full length of the trommel drum for ground level service and removal.
- A hydraulic-driven chain drive system allows the drum to be lifted off the cog for service, and bolt-on sprockets can be changed quickly to help lower repair time.
- The TR5300 features a large, low-feed hopper that makes it easier to load with a loading ramp, making the trommel screen more mobile around the jobsite.
Online Brochures
General Dimensions and Weights
| Weight | 32000 lbs | 14515 kg |
| Hitch Weight | 11600 lbs | 5261.7 kg |
| Transport Length | 39 ft | 11.9 m |
| Transport Width | 98.4 in | 249.9 cm |
| Transport Height | 13.4 ft | 4.1 m |
| Operation Length | 89.9 ft | 27.4 m |
| Operation Width | 112.8 in | 286.5 cm |
| Operation Height | 15 ft | 4.6 m |
| Capacity | 100 cu yd (76.5 m3) per hr with .5" (12.7 mm) screens installed and material with moisture less than 40% |
Engine Option One
| Make and Model | Deutz TD2.9L Tier 4 Final/ Stage IV | |
| Number of Cylinders | 4 | |
| Engine Rating | 74 hp (55 kW) @ 2600 rpm and 181 ft-lb (245.4 Nm) of torque @ 1600 rpm | |
| Fuel Tank Capacity | 44 gal | 166.6 L |
| Fuel Consumption | 4.6 | |
| Maximum Engine Operating Angle (Operating angles do not indicate safe machine operating angles) | 30 deg | |
| Battery | 950 Cold Cranking Amp Group 31 | |
| Oil Filter | Spin-on | |
| Recommended Oil | Mobil 15W40 | |
| Oil Volume with Filter | 8.4 qt | 7.9 L |
| System Voltage | 12 | |
| Air Cleaner | Dual element | |
| Radiator Fan | Suction |
Hydraulic System
| Tank capacity | 55 gal | 208.2 L |
Chassis
| Frame Description | Heavy Duty Structural Tubing | |
| Axle/Suspension | Single Leaf Sprung | |
| Capacity | 20000 lbs | 9071.8 kg |
| Tires - Option One | 445/50R22.5 |
Hopper and Apron Conveyor
| Hopper Capacity | 5.5 cu yd | 4.2 cu m |
| Hopper Bottom Width | 34 in | 86.4 cm |
| Hopper Height | 9.5 | |
| Hopper Opening | 34x37 |
Screen Drum
| Drum Operation | 0-30.9 gpm (0-117.0 L/min) | |
| Drum Diameter | 5 ft | 1.5 m |
| Drum Support Description | Eight poly trunnion rollers 8" (20.3 cm) diameter 4" (10.2 cm) width | |
| Thrust Bearing Diameter | 4 in | 10.2 cm |
| Thrust Bearing Face | 2.9 in | 7.4 cm |
| Drum Speed | 0-24 RPM | |
| Drum Drive Chain | 140 custom extended pin | |
| Drum Angle Adjustability | 0-7 degrees | |
| Maximum Screen Panels | 4 |
Screen Brushes
| Brush Diameter | 14 in | 35.6 cm |
| Bristle Material | Polyethylene | |
| Brush Assembly Support | Two 1.25" (3.2 cm) sealed ball bearings |
Fines Conveyor
| Conveyor Operation | 17 gpm | 64.4 L/min |
| Conveyor Motor Displacement | 33 cu-in | 540.8 cu-cm |
| Fines Conveyor Length | 55 ft | 16.8 m |
| Fines Belt Speed | 500 ft/min | 152.4 m/min |
| Conveyor Belt Width | 36 in | 91.4 cm |
| Conveyor Belt Type | 220 lb, 2 ply, 3/16" x 1/16", R2 splice, Continuous option | |
| Conveyor Belt Stacking Height | 15' | |
| Head Pulley Type | Rubber lagged, 12" (30.5 cm) diameter, 38" (96.5 cm) wide | |
| Head Pulley Bearing | 2 7/16" (6.2 cm) pillow block | |
| Troughing Idler Type | 20° CEMA "B" with permanently sealed bearings | |
| Self-Cleaning Tail Pulley Dimensions | 10" (25.4 cm) diameter, 38" (96.5 cm) wide with 2.4" (6.1 cm) shaft | |
| Head Pulley Takeup | 10 in | 25.4 cm |
| Self-Cleaning Return Idlers | 4" (10.2 cm) rubber disc, qty 8 | |
| Fines Conveyor Frame | 2" (5.1 cm) x 8" (20.3 cm) structural steel tubing |
Overs Conveyor
| Overs Conveyor Length | 10.5 ft | 3.2 m |
| Maximum Variable Overs Belt Speed | 350 ft/min | 106.7 m/min |
| Conveyor Belt Size | 36 | |
| Conveyor Belt Type | 220 lb, 2 ply, 3/16" x 1/16", R2 splice, Continuous option | |
| Conveyor Belt Stacking Height | 6' | |
| Head Pulley Type | Rubber lagged, 12" (30.5 cm) diameter, 38" (996.5 cm) wide | |
| Head Pulley Bearing | 2 7/16" (6.2 cm) pillow block | |
| Self-Cleaning Tail Pulley Dimensions | 10" (25.4 cm) diameter, 38" (96.5 cm) wide with 2.4" (6.1 cm) shaft |
