Vermeer SC382

The SC382 was made for the tough stumps on your jobsite. This Vermeer stump cutter is equipped with a 37 hp (26.1 kW) EFI Briggs and Stratton Vanguard engine. The optimized cutting wheel on the SC382 gives this machine aggressive cutting capabilities. Along with standard four-wheel drive and the optional front blade, this model is the full package for stump cutting from start to finish.

  • The SC382 stump cutter is equipped with standard four-wheel drive to offer traction and maneuverability in difficult transport conditions.
  • The operator presence system is intended to enhance operator safety by automatically stopping the cutter wheel when the operator releases the hydraulic cutter wheel controls.
  • The optional hydraulic front blade helps to reduce the amount of manual work during jobsite clean-up.
  • The SC382 stump cutter has a 37 hp (26.1 kW) EFI Briggs and Stratton Vanguard engine.
Online Brochures
Length 118 in 299.7 cm
Width 50.1 in 127.3 cm
Height 53 in 134.6 cm
Overall Width Transport (without duals) 35.5 in 90.2 cm
Weight - Engine Option One 1950 lbs 884.5 kg
Weight With Chip Blade Option (Additional) 85 lbs 38.6 kg
Make and Model Briggs & Stratton Vanguard EFI
Number of Cylinders 2
Gross Horsepower (Maximum) 37 hp 27.6 kw
Torque (Max) 49 ft-lb 66.4 Nm
Fuel Tank Capacity 10 gal 37.9 L
Max Fuel Consumption 3.2 gph 12.1 lph
Fuel Type Gas
Air Cleaner Dry-type safety element and restriction indicator
Oil Filter Spin-on
Recommended Oil 10W30 (See engine manual)
Oil Volume with Filter 2.5 qt 2.4 L
Maximum Angle of Continuous Operation 25 deg
Cooling Medium Air
Alternator 20/50 amp (rpm-based)
Clutch Type Electric clutch with brake
Cutterwheel Diameter without Teeth 17 in 43.2 cm
Cutterwheel Thickness .5 in 1.3 cm
Cutterwheel Speed 1560 rpm
Cutterwheel Straight Line Dimension 47 in 119.4 cm
Cutterwheel Cut Above Ground 24 in 61 cm
Cutterwheel Cut Below Ground 15 in 38.1 cm
Tooth Description Yellow Jacket cutter system
Number of Teeth 20
Number of Indexes 2
Number of Pockets 20
Reversible Pockets 20
Cutterwheel Guard Standard
Chip Containment 7.5 cu ft .2 cu m
Belt Type V-belt
Number of Primary Belts 2 individual (matched pair)
Jackshaft Dimension 1.3
Jackshaft Bearing Type Sealed ball
Bearing Dimensions 1.3 bore
Number of Secondary Belts 6 banded
Cutterwheel Shaft 1.8" (4.8 cm)
Bearing Dimensions - Secondary Belt 1.8" (4.8 cm) double spherical roller pillow block
Tank capacity 6.5 gal 24.6 L
Recommended Oil Type Vermeer HyPower 68
System Type Open-loop series system
Filtration Method 10 micron fill strainer and 6 micron return filter
Pump Flow at Maximum RPM 6.4 gpm 24.2 L/min
System relief pressure 2470 psi 170.3 bar
Flow Control SmartSweep
Directional Control Electric over hydraulic
System Voltage 12 V
Battery 400 CCA
Warning Lights Oil pressure, engine fault, operator presence status, clutch engage/disengage status
Switches Two-speed 2x4 and 4x4 ground drive, cutter wheel engage/disengage, creep, blade (if applicable)
Controller Danfoss
Shutdown System Engine low oil pressure
Frame Description Welded tube and plate steel
Control Station Description Fixed side location
Toolbox Description Standard
Steerable Axle Type Hydraulic steering, oscillating axle
Degree of Oscillation 12 deg
Tires - Option One 5.7"x 8" (14.5 x 20.3 cm) dual standard
Fender Description Yes
Axle/Suspension Rigid/fixed (rear)
Brake Type Spring-applied, hydraulic release at rear motors
Low Speed Travel 65 ft/min 19.8 m/min
High Speed Travel 130 ft/min 39.6 m/min
Chip Blade Dimension Optional - 33" (83.8 cm) wide, 12" (30.5 cm) tall
Blade Travel Above Ground 8 in 20.3 cm
Blade Travel Below Ground 2.5 in 6.4 cm