The H340 and H360 Loaders can be ordered with a single-point hydraulic connection that also incorporates the connection point for any electrical needs. To disconnect the hydraulic connection between the loader and the tractor, it is necessary to relieve the hydraulic system oil pressure on the tractor.
Over time, increased width in tractor hoods have caused issues with available space for running traditional oil lines of a loader along the boom, making them more susceptible to damage.
To improve this situation, the oil lines have been routed through the boom arm and the torque tube, improving line protection and the appearance of the loader.
John Deere loaders are easily removed and reinstalled on tractors without tools. The parking system allows removing or attaching the loader to the tractor in minutes without the need for tools.
To remove or park the loader, apply slight down pressure to the loader boom with the bucket dumped at approximately a 30-degree angle. With the tractor in park, install the parking stands and place the mast pins in the open position.
To watch a video of parking and attaching an H-Series loader, click here.
Utilizing the boom circuit with the tractor in neutral, rotate the mast forward until the mast has rotated past the pin location on the mounting frame by extending the lift cylinder. Now using the bucket circuit, roll back the bucket until the mast is removed from the pocket and will clear the tires.
With the tractor in park, shut the engine off and relieve the hydraulic pressure as indicated for the tractor. Relieve pressure on the single-point hydraulic connection, then disconnect or open the single-point hydraulic connector.
Store the loader half of the single-point connector. The tractor is now ready to back away from the loader.
A hydraulic shut-off valve is included with the H-Series Ag Loaders to ensure the loader does not lower suddenly. For example, this allows the boom to be locked out when someone is required to be located under the loader boom for service work on the tractor. It should not be used for extended periods of time unless an appropriate support stand is also utilized.
Fast bucket cycle times are important to dump the load from the bucket as quickly as possible (quite often) in order to be as productive as possible while completing loading operations. The bucket cylinder design can have a major impact on this cycle time, especially for the MSL loaders.
Therefore, all MSL H-Series Loaders utilize false rod bucket cylinders. A false rod cylinder has a smaller displacement of oil requirement on the head end of the cylinder, which allows this cylinder to dump much faster than a normal cylinder.
An enhancement to the loader is the suspension system. A great level of loader productivity is achieved with the LSS.
NOTE: Check bale-handling capability of tractor before use.
Cost of ownership
Reasons for turning LSS off include:
The switch is conveniently located in the operator station to avoid having to exit the tractor seat to manually move the handle on the LSS.
LSS can also be ordered with a manual shutoff. Depending on the tractor/loader model, the accumulator is located in different places. On the 440R, the accumulator is mounted outside the bottom of the mounting frame. On the 5 Series Tractors, the accumulator is mounted near the inside of the rear right wheel. On 6 Series tractors and larger, it is mounted in between the hydraulic connection and the mounting frame.
The RTP option for 6R Tractors and H340, H360, and H380 Loaders provides superior productivity and repeatability during material handling operations. An industry exclusive, RTP allows the operator to store two boom positions and two bucket positions through the use of sensors, the tractor’s CommandCenter™, and controller. To watch a video of a loader using RTP click here.
With a simple activation of the momentary detents on the electronic joystick, the loader will return to the preset positions. A complete loading cycle now can be accomplished with four movements of the joystick thus significantly improving productivity. Operator stress is also significantly reduced as there is no need to constantly check the loader height and attachment angle during the operation.
The RTP option also incorporates another industry exclusive with the electronic self-leveling (ESL) feature. ESL utilizes the same components as RTP to provide self-leveling capability without the use of mechanical linkages or complex hydraulics.
When the RTP option is installed on a non-self-leveling (NSL) loader, the ESL functionality transforms it into a self-leveling loader. If the a material handling operation does not call for the repeatability of RTP and the self-leveling functionality of ESL, the operator can simply deactivate the system and utilize the loader in the traditional NSL manner.
For operators demanding superior lift capacity and productivity, RTP can be installed on a mechanical self-leveling (MSL) loader as well. While RTP will enhance the repeatability, the ESL feature will improve the leveling accuracy of the MSL loader.
Since the RTP option does not affect the base characteristics of the loader (for example, lift capacity and breakout force), operators need to carefully choose the appropriate loader for their material handling needs. The below chart shows the benefits RTP will offer customers when installing on either a NSL or MSL loader.
|Rollback limitation at full height|
|Boom breakout force|
|Bucket rollback cycle times|
|Bucket dump cycle times|
|Boom raise/lower cycle times|
|Capable of storing two boom and two bucket positions|
NOTE: Refer to the sales manual or operator’s manual (OM) for complete list of loader specifications.
The RTP operator interface consists of one single screen within the CommandCenter for simple, straightforward setup and operation. Through this screen, the operator is easily able to activate the system, store two boom and two bucket positions, set the zero position for the attachment, and monitor the boom and bucket positions.
Once the operator has saved the two boom positions with buttons (G) and (H) and the two bucket positions with (B) and (C) in the CommandCenter, the operator initiates the automatic functions through the use of the electronic joystick’s momentary detents.
RTP is only compatible with 6R Tractors equipped with electronic joysticks and electronic independent control valves (E-ICVs). On the loader side, RTP is compatible with H340s, H360s, and H380s as long as they include the single-point hydraulic connection (single-point connection is included in the 6R Loader ready packages and is the only connection option available for the H380). RTP is not compatible with loader suspension, but it is compatible with both Triple-Link Suspension (TLS™) and cab suspension available on the 6R Tractors.
Once the loader components have been installed and the loader is mounted to the 6R Tractor, a calibration must be performed by a dealer service technician. This simple calibration procedure is only required to be performed once unless a sensor or linkage is replaced or the loader is installed onto another 6R equipped with the RTP option.
|Front axle configuration||MFWD w/ Limited Slip Differential|
|Pump capacity||79.5 L/min|
|Rated pressure||200 bar|
|Leveling configuration||Non-Self Leveling (NSL)|
|Bucket used||Heavy Duty 2450 mm|
Heavy Duty 96 in.
|Bucket weight||358 kg|
|Lift capacity at full height||Measured at pivot (U)|
4063 lb Measured at 800 mm ahead of pivot (V)
|Lift capacity at 59 in. (1500 mm)||Measured at pivot (W)|
5959 lb Measured at 800 mm ahead of pivot (X)
|Boom breakout force||Measured at pivot (Y)|
7919 lbf Measured at 800 mm ahead of pivot (Z)
|Bucket rollback force capacity||At ground-level line (ZZ)|
|Dimensions||Maximum lift height (A)|
168.5 in. At full height - bucket level(B)
160.1 in. At full height - bucket dumped (C)
|Overall length (I+F), ft (m)|
|Overall height in carry position (J)|
|Digging depth (H)||125 mm|
|Reach||At maximum height (D)|
27.5 in. At ground level - bucket level (F)
|Bucket angle||Dump angle, degrees (E)|
-55 degree (angle)Rollback angle, degrees (G)
33 degree (angle)Dump angle, ground
-142 degree (angle)
|Cycle times||Loader raise, seconds|
4.19 seconds Loader lower, seconds
2.87 seconds Bucket dump, seconds
2.31 seconds Bucket rollback, seconds
© 2019, RDO Equipment Co. All Rights Reserved.